With the aggravation of the market competition, the price of the car girder calibrator is getting lower and lower. Under the premise of low profit, the manufacturer will not send personnel to the site for equipment installation and commissioning. Some employees of maintenance enterprises have used the car beam calibrator, and some new enterprises have never been exposed to this situation. What should we do?

　　濟南奔馳汽車維修哪家好

　　Which is the best car repair shop for Jinan Benz

　　很簡單:遵循調試步驟。安裝調試步驟如下:

　　Simple: follow the debugging steps. The installation and debugging steps are as follows:

　　一個:卸載。目前市場上使用叉車卸車更為方便。叉車必須配備伸直的手臂，這通常被稱為伸直的腿。由于超級棒梁校直器的長度一般為5米和6米，如果沒有伸出胳膊(伸直腿)，就不夠長，使用起來也不方便。(如叉車使用不方便，也可使用吊車)在放置橫梁校準儀時，由于小車從起升油缸一側上升，應將起升油缸的端部翻出。

　　One: uninstall. At present, forklift is the most convenient to unload in the market. Forklifts must be equipped with straight arms, which are often referred to as straight legs. As the length of the super bar straightener is generally 5M and 6m, it is not long enough and inconvenient to use if the arm (straight leg) is not extended. (if the forklift is not convenient to use, the crane can also be used.) when placing the beam calibrator, because the trolley rises from one side of the lifting cylinder, the end of the lifting cylinder should be turned over.

　　二:吊主鏈和斜吊臂。將光束校驗儀放置在預定位置后，用鈑金工具拆卸木箱，找到主鏈。吊鏈前應安裝斜臂，斜臂上應安裝帶鏈條的u型鏈吊架。然后掛起一根鏈條，將鏈條與未鉤端相連，首先穿過u形的鏈條吊架，然后穿過導向環，穿過頂桿帽。注意:鏈條不允許打結或扭曲。安裝鏈條后，一定要安裝鏈條保護器。

　　2： Crane main chain and inclined boom. After the beam calibrator is placed in the predetermined position, use the sheet metal tool to remove the wooden box and find the main chain. The inclined arm shall be installed before the lifting chain, and the U-shaped chain hanger with chain shall be installed on the inclined arm. Then hang a chain, connect the chain with the uncoupled end, first through the U-shaped chain hanger, then through the guide ring, and finally through the top bar cap. Note: the chain shall not be knotted or twisted. After installing the chain, be sure to install the chain protector.

　　三:連接油管(主要用于氣動泵)。箱內有兩個氣動泵和兩個油管，箱內裝有鈑金件。首先將油管連接到氣動泵上，注意用原材料包裹，防止漏氣。當次使用,因?yàn)橛袣堄鄽怏w在油缸,所以在使用前必須先排氣(打開旁邊的排氣閥氣動泵踏板),結束的氣動泵連接到空氣源、油管快速連接到其他媒體在地上,按氣動泵,直到石油耗盡。然后將管子的一端(快速連接)連接到拉塔的氣缸上，將腳壓在氣泵上。此時，油缸將會上升，拉塔中的千斤頂桿也會上升。測試完后，試一下平臺上傾斜的油缸。

　　3： Connect oil pipe (mainly used for pneumatic pump). There are two pneumatic pumps and two oil pipes in the box, and the box is equipped with sheet metal parts. First, connect the oil pipe to the pneumatic pump, and wrap it with raw materials to prevent air leakage. When using for the first time, because there is residual gas in the cylinder, it is necessary to exhaust before using (open the pneumatic pump pedal of the side exhaust valve), connect the end pneumatic pump to the air source, connect the oil pipe to other media quickly on the ground, press the pneumatic pump until the oil is exhausted. Then connect one end of the pipe (quick connect) to the cylinder of the tower and press the foot on the air pump. At this time, the cylinder will rise and the jack rod in the tower will rise. After the test, try the tilt cylinder on the platform.

　　四、一步是鈑金。板料零件可以掛在板車上。

　　4、 The final step is sheet metal. Sheet metal parts can be hung on the board car.

　　以上是濟南奔馳汽車維修公司小編為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.nhakhoathuduc.net

　　These are the related contents introduced by the small edition of Jinan Benz automobile maintenance company. If you want to know more, please visit the website: http://www.lutongqixu.com